熱線電話:

鴻御(上海)國際貿易有限公司

主營:江蘇SKF軸承,江蘇FAG軸承,江蘇IN...

商鋪首頁 > 新聞動態 > 徐州NSK軸承61805減輕常見原因造成的損傷
鴻御(上海)國際貿易有限公司
4
企業等級: 銀品會員
經營模式:
所在地區: 上海 上海
聯系賣家:    QQ在線咨詢524085168
手機號碼:
公司官網: www.wh-skf.com
公司地址:

徐州NSK軸承61805減輕常見原因造成的損傷

發布時間:2019-01-08 06:14:03        

減速器徐州NSK軸承的損壞是一個常見問題。除了軸承本身的質量問題外,常點減速器還列出了軸承損壞的其余原因,供您參考。

Damage of NSK bearing in Xuzhou reducer is a common problem. In addition to the quality problems of the bearing itself, the c***tant point reducer also lists the other causes of bearing damage for your reference.

1:軸承室不干凈,沒有油。軸承具有額定負荷高、噪音低、大大降低維護成本、延長機器運行時間等優點。例如,軸承保持架內的微小剛性材料沒有徹底清洗,軸承滾道在運行中損壞,導致軸承溫升過高,燒壞軸承。

1: The bearing room is not clean and there is no oil. Bearing has the advantages of high rated load, low noise, greatly reducing maintenance costs and prolonging machine operation time. For example, the tiny rigid material in the bearing cage has not been thoroughly cleaned, and the bearing raceway is damaged in operation, resulting in excessive temperature rise of the bearing and burning out the bearing.

2:由于電機本體溫升過高,徐州NSK軸承補油不足,導致軸承缺油甚至燒壞。

2: Because of the excessive temperature rise of the motor body, Xuzhou NSK bearings are insufficient in oil replenishment, resulting in oil shortage or even burnout of bearings.

3:軸承裝配不當,如冷負荷下軸承內圈攻絲不均,造成軸磨損,造成軸承內圈與軸承干涉損失,或減少干涉,導致內圈運轉。電機端蓋攻絲不均,導致軸承腔與軸承外圈配合不當,造成外圈偏移。通過觸摸軸承上的鋼印,可以更快、更準確地識別軸承。如果你用手觸摸***,你就感覺不到了。然而,鋼印的存在可以用釘子觸摸。內圈或外圈是否會引起軸承的溫升急劇上升和燒壞,特別是內圈的失效會導致徐州NSK軸承軸的轉動。嚴重磨損和彎曲。然而,外環的間歇運行通常不會導致軸承溫度急劇上升。只要軸承狀況良好,允許外環間歇運行。

3: improper assembly of bearing, such as uneven tapping of bearing inner ring under cold load, resulting in shaft wear, resulting in interference loss between bearing inner ring and bearing, or reducing interference, leading to inner ring operation. The uneven tapping of motor end cap results in improper matching between bearing chamber and bearing outer ring, resulting in outer ring offset. By touching the steel stamp on the bearing, the bearing can be recognized more quickly and accurately. If you touch the stamp with your hand, you won't feel it. However, the existence of steel stamps can be touched by nails. Whether the inner ring or outer ring will cause the temperature rise of the bearing to rise sharply and burn out, especially the failure of the inner ring will lead to the rotation of Xuzhou NSK bearing shaft. Severe wear and bending. However, the intermittent operation of the outer ring usually does not lead to a sharp rise in bearing temperature. The outer ring is allowed to run intermittently as long as the bearing is in good condition.

4:由于定、轉子鐵心軸向錯位或加工后轉軸重新對中精度低,軸承內外圈不在切向平面內,使軸承運轉無硬化,后期溫升燒壞。

4: Because of the axial misalignment of stator and rotor cores or the low accuracy of re-alignment of rotating axles after processing, the inner and outer rings of bearings are not in the tangential plane, which makes the bearings run without hardening, and the later temperature rise burns out.

5:更換徐州NSK軸承后,過度干涉或橢圓電機端蓋套會導致球隙過小或不均勻,導致摩擦增大,溫度急劇上升,直至燒壞。

5: After the replacement of Xuzhou NSK bearing, excessive interference or elliptical motor end cover will lead to too ***all or uneven ball clearance, resulting in increased friction, temperature rise sharply until burnout.

6:軸承因混合不同類型的潤滑脂而損壞。

6: Bearings are damaged by mixing different types of grease.

7:備用機器長時間不運轉,油脂變質,軸承生銹,未修理。當徐州NSK軸承識別出軸承的真實性時,通過觸摸軸承上的鋼印,可以更快、更準確地識別軸承的真實性。如果用手觸摸,***是不可觸摸的,但可以用釘子觸摸***。

7: Standby machine is not running for a long time, grease deterioration, bearing rust, not repaired. When Xuzhou NSK bearing recognizes the authenticity of the bearing, it can recognize the authenticity of the bearing more quickly and accurately by touching the steel seal on the bearing. Stamps are not touchable if touched by hand, but they can be touched by nails.

對于上述七種情況,您可以比較在使用過程中遇到的問題。如果是這樣,立即改進延長減速器軸承的使用。

For the above seven cases, you can compare the problems encountered in the use process. If so, immediately improve the use of extended reducer bearings.

 

文章來自:徐州SKF軸承 www.wh-skf.com

Article from: Xuzhou SKF Bearing www.wh-skf.com

文章來自:徐州INA軸承 www.ina-china.cn

Article from: Xuzhou INA Bearing www.ina-China.cn

文章來自:徐州NSK軸承 www.klbbearings.com

Article from: Xuzhou NSK Bearing www.klbbearings.com

 

***:524085168

電話:0510-81207777

手機:13311666672/13395185757

 

免責聲明
? 本文僅代表作者個人觀點,本站未對其內容進行核實,請讀者僅做參考,如若文中涉及有違公德、觸犯法律的內容,一經發現,立即刪除,作者需自行承擔相應責任。涉及到版權或其他問題,請及時聯系我們 304108043@qq.com
  • QQ在線咨詢524085168
  • 手機:
  • 聯系我時務必告知是在產品網上看到的!

鴻御(上海)國際貿易有限公司

商鋪|誠信檔案

地址:

電話:傳真:

免責聲明:以上信息由會員自行提供,內容的真實性、準確性和合法性由發布會員負責,產品網對此不承擔任何責任。產品網不涉及用戶間因交易而產生的法律關系及法律糾紛, 糾紛由您自行協商解決。

風險提醒:本網站僅作為用戶尋找交易對象,就貨物和服務的交易進行協商,以及獲取各類與貿易相關的服務信息的平臺。為避免產生購買風險,建議您在購買相關產品前務必 確認供應商資質及產品質量。過低的價格、夸張的描述、私人銀行賬戶等都有可能是虛假信息,請采購商謹慎對待,謹防欺詐,對于任何付款行為請您慎重抉擇!如您遇到欺詐 等不誠信行為,請您立即與產品網聯系,如查證屬實,產品網會對該企業商鋪做注銷處理,但產品網不對您因此造成的損失承擔責任!

聯系:304108043@qq.com是處理侵權投訴的專用郵箱,在您的合法權益受到侵害時,歡迎您向該郵箱發送郵件,我們會在3個工作日內給您答復,感謝您對我們的關注與支持!

商鋪首頁 | 公司概況 | 供應信息 | 新聞動態 | 誠信檔案 | 聯系我們 |

鴻御(上海)國際貿易有限公司 電話: 傳真: 聯系人:

地址: 主營產品:江蘇SKF軸承,江蘇FAG軸承,江蘇INA軸承,江蘇NSK軸承,浙江SKF軸承,浙江FAG軸承,浙江INA軸承,浙江NSK軸承

Copyright © 2021 版權所有: 產品網    粵ICP備07513236號

免責聲明:以上所展示的信息由企業自行提供,內容的真實性、準確性和合法性由發布企業負責。產品網對此不承擔任何保證責任。

商盟客服

您好,歡迎蒞臨,歡迎咨詢...